HP LASERJET M631 M632 M633 PRINTER REPAIR SERVICE | FUSER ERROR | PAPER JAM
HP Laserjeet M631 MFP Printer Repair Service
HP Laserjet MFP M631 Paper Jam
HP Laserjet MFP M631 Fuser Error
HP Laserjet MFP M631 Perform Maintenance
HP LASERJET M631 M632 M633
INTRODUCTION DATE (MAY 2017)
PRINT SPEED
55 PAGES PER MINUTES
TONER CARTRIDGES
CF237A (11,000 PAGES YIELD)
CF237X (25,000 PAGES YIELD)
CF237Y (41,000 PAGES YIELD)
MAINTENANCE KIT PART NUMBER
J8J87A
FUSER ASSEMBLY
RM2-1256-020-000
SEPARATION and PICKUP FEED ASSEMBLY
J8J70-67904
HP 300 ADF ROLLER REPLACEMENT KIT
J8J95A
HP Laserjeet M632 MFP Printer Repair Service
HP Laserjet MFP M632 Paper Jam
HP Laserjet MFP M632 Fuser Error
HP Laserjet MFP M632 Perform Maintenance
HP LASERJET M631 M632 M633
INTRODUCTION DATE (MAY 2017)
PRINT SPEED
55 PAGES PER MINUTES
TONER CARTRIDGES
CF237A (11,000 PAGES YIELD)
CF237X (25,000 PAGES YIELD)
CF237Y (41,000 PAGES YIELD)
MAINTENANCE KIT PART NUMBER
J8J87A
FUSER ASSEMBLY
RM2-1256-020-000
SEPARATION and PICKUP FEED ASSEMBLY
J8J70-67904
HP 300 ADF ROLLER REPLACEMENT KIT
J8J95A
HP Laserjeet M633 MFP Printer Repair Service
HP Laserjet MFP M633 Paper Jam
HP Laserjet MFP M633 Fuser Error
HP Laserjet MFP M633 Perform Maintenance
HP LASERJET M631 M632 M633
INTRODUCTION DATE (MAY 2017)
PRINT SPEED
55 PAGES PER MINUTES
TONER CARTRIDGES
CF237A (11,000 PAGES YIELD)
CF237X (25,000 PAGES YIELD)
CF237Y (41,000 PAGES YIELD)
MAINTENANCE KIT PART NUMBER
J8J87A
FUSER ASSEMBLY
RM2-1256-020-000
SEPARATION and PICKUP FEED ASSEMBLY
J8J70-67904
HP 300 ADF ROLLER REPLACEMENT KIT
J8J95A
HP LaserJet Enterprise MFP M631, M632, M633, Managed MFP E62555-E62575, E62655-E62675 –
A “30.01.41” or “30.03.45” scanner error displays on the printer control panel
HP LaserJet Enterprise MFP M631, M632, M633, MFP E62555-E62575, E62655-E62675 – A “30.01.41” or “30.03.45” scanner error displays on the printer control panel
Problem
HP LaserJet Enterprise MFP M631, M632, M633, MFP E62555-E62575, E62655-E62675 – A “30.01.41” or “30.03.45” scanner error displays on the printer control panel
Problem
In case one of the preceding error messages displays on the HP Laserjet printer display, it suggests that there was an concern with the scanner control board:
30.01.41 Scanner error
30.03.45 Scanner error. To continue turn off and turn back on
A 30.01.41 Scanner error may display in the preceding cases:
Following the HP Laserjet printer comes out of Sleep mode
After opening/closing the Automatic Document Feeder multiple times
After power up the HP Laserjet printer
In these kinds of cases, the issue can very likely be solved by upgrading the firmware latest revision.
Consult the following webpage with regard to the latest firmware version
https://support.hp.com/us-en/drivers/selfservice/hp-laserjet-enterprise-mfp-m632-series/9364944
Consider the appropriate actions to fix the condition:
Turn the printer off and then back on.
Upgrade the firmware on the HP Laserjet printer.
If the malfunction persists after upgrading the firmware, contact Printer Repair Experts Customer Care (888) 276-4666 for extended support.
HP LaserJet Enterprise MFP M631, M632, M633, Managed MFP E62555-E62575, E62655-E62675 –
A “30.01.41” or “30.03.45” scanner error displays on the printer control panel
HP LaserJet Enterprise MFP M631, M632, M633, MFP E62555-E62575, E62655-E62675 – A “30.01.41” or “30.03.45” scanner error displays on the printer control panel
Problem
HP LaserJet Enterprise MFP M631, M632, M633, MFP E62555-E62575, E62655-E62675 – A “30.01.41” or “30.03.45” scanner error displays on the printer control panel
Problem
In case one of the preceding error messages displays on the HP Laserjet printer display, it suggests that there was an concern with the scanner control board:
30.01.41 Scanner error
30.03.45 Scanner error. To continue turn off and turn back on
A 30.01.41 Scanner error may display in the preceding cases:
Following the HP Laserjet printer comes out of Sleep mode
After opening/closing the Automatic Document Feeder multiple times
After power up the HP Laserjet printer
In these kinds of cases, the issue can very likely be solved by upgrading the firmware latest revision.
Consult the following webpage with regard to the latest firmware version
https://support.hp.com/us-en/drivers/selfservice/hp-laserjet-enterprise-mfp-m632-series/9364944
Consider the appropriate actions to fix the condition:
Turn the printer off and then back on.
Upgrade the firmware on the HP Laserjet printer.
If the malfunction persists after upgrading the firmware, contact Printer Repair Experts Customer Care (888) 276-4666 for extended support.
HP LASERJET M631 MFP FUSER ERROR
HP LASERJET M632 MFP FUSER ERROR
HP LASERJET M633 MFP FUSER ERROR
The 59 error codes indicates a specific motor failure – HP Laserjet M631, M632, M633 printers
59.xx.00 – This means issues associated to the tray 2 lift motor.
To resolve this malfunction, remove the tray two cassette and confirm the gear as well as the one-quarter gear located at the rear left side of the tray 2 paper cassette, rotates freely.
Examine the lifter gear messhes correctly with these gears within the rear left corner of the HP Laserjet M631, M632, M633 printer.
Ensure the connection at J206 within the DC Controller is safe and sound and that its wires are not pinched or affected.
exchange the lifter drive assembly . If error carries on, begin to following step
replace the DC Controller PCB
59.xx.30 / 59.xx.40 – This exhibits problems connected to the fuser assembly motor.
Replace Fuser Assembly
If any service and repairs have recently been carried out on the HP Laserjet M631, M632, M633, ensure the connection at J204 on the DC Controller is secure and the wires are not constricted or damaged.
If the J204 connection appears to be ok, replace the fuser drive assembly.
In the event that the error persists, swap the DC Controller PCB
59.xx.50 59.xx.60 – This means an issue linked to the Drum Motor.
Exchange the toner cartridge,
If any service and repairs have recently been performed on the HP Laserjet M631, M632, M633, ensure the connection with J203 on the DC Controller is secure and that its wires are not constricted or damaged. If the J203 connection looks to be acceptable, run the drum motor component test
Swap the drum motor, if error persist then move forward to the following task.
Replace the DC Controller PCB.
HP LASERJET M631 MFP PAPER JAM
HP LASERJET M632 MFP PAPER JAM
HP LASERJET M633 MFP PAPER JAM
HP LASERJET MFP M631, M632, M633 PAPER JAM ERROR CODES
HP LASERJET M631 MFP , M632 MFP, M633 MFP PAPER JAM
A paper jam is actually a phase express when media gets lodged inside of a printer and its unable to ejecting. When this occurs within the HP Laserjet M631, M632, M633 Printer may not operate appropriately until the pages has been physically taken away.
13.00 Paper Jam
Details:
Unidentified door open
Course of Action:
Verify that each of the cover / doors are closed.
13.A3 Paper Jam
Details:
Power on jam within cassette tray 3 feed sensor.
Course of Action:
Check the product for any jam. Note the clear jams page inside service guide.
13.D3 Paper Jam
Details:
Delayed to duplex re-feed jam
◦ 13.D3.D1 Paper Jam
Course of Action
Scan the HP product for a paper jam. Note the clear jam page within the service manual.
13.E5 Paper Jam
Details
A power on jam has developed.
Course of Action
Examine the HP Printer for a paper jam.
13.EA Paper Jam
Details
An open door jam has developed.
Course of Action
Look through the product for the paper jam. Try performing the component test to isolate a bad door switch or sensor.
13.EE Paper Jam
Details
A power up jam has occured.
Course of Action
Look through the HP Product for the jam.
13.FF.EE Paper Jam
Details:
A door jam has occurred.
Course of Action
Examine the HP printing device for any paper jam. Access the Manual sensors test and / or Tray/Bin manual sensors check to verify a faulty door switch and / or sensor.
13.WX.EE Paper Jam
Details:
This particular paper jam happens whenever a door is opened during the course of printing.
Course of Action
Make sure the doors are fully closed.
13.WX.FF Paper Jam
Details
Power on residual paper jam. This jam happens when the prints exists at the paper path jam sensors at power up or door close. As a result of the most current FW timing prerequisites, the demonstrated jamming code is continually 13.FF.FF, only the Log history will display 13.WX.FF
Recommended action:
Check the HP Product for the paper jam.
Replace Feed Separation Rollers
13.WX.YZ Fuser Area Jam
Details:
A jam in the fusing assembly region has manifested.
Course of Action:
Remove the jam.
Ensure paper satisfies specifications, search for obstructions inside fusing assembly, check that the T2 roller is seated properly.
Replace Fuser Assembly
13.WX.YZ Fuser wrap jam
Course of Action
Remove the jam.
Replace Fuser Assembly
13.WX.YZ Paper Jam below control panel
Details
◦ 13.B2.9Z (event code)
paper at duplex switchback jam.
Z = the source tray number
Course of Action
Look throughout the HP printing device for the jam.
Replace Feed Separation Rollers
13.WX.YZ Paper Jam in Tray 1
Details
◦ 13.B2.D1 (event code)
Late to registration jam, from Tray 1
This jam appears the moment the prints doesn’t reach the TOP sensor in assigned total amount of time starting from the start of media pickup at printing from manual feed tray & duplex printing.
Course of Action
Remove the media jam.
13.WX.YZ Paper Jam in Tray <X>
Details
A misfeed paper jam has appeared.
Course of Action
Eliminate the paper jam.
Replace Tray 1 Paper Feed Roller. Replace Tray 1 Separation Rollers
13.WX.YZ jam inside envelope feeder
Details
A paper jam exists within the envelope feeder.
Course of Action
Clear out the jam.
13.WX.YZ Paper Jam within top cover
Details
A jam rests on the inside the top cover.
Course of Action
Clear out the paper jam.
HP LASERJET MFP M631 50 FUSER ERROR
HP LASERJET MFP M632 50 FUSER ERROR
HP LASERJET MFP M633 50 FUSER ERROR
HP LASERJET M631, M632, M633 FUSER ERROR
50.1 Fuser Error
Low Fusing Assembly temperature problem
50.2 Fuser Error
fuser heat up error
50.3 Fuser Error
High fuser temperature
50.4 Fusing Error
Drive circuit failing
50.6 Fuser Error
Open Fusing Assembly circuit (breakdown of the heating component)
50.7 Fuser Error
Fusing Assembly pressure-release mechanism breakdown
50.8 Fuser Error
Low Fusing Assembly temperature II
50.9 Fuser Error
High Fusing Assembly temperature II
I needed help with my Brother printer. Greg asked me a few questions about my printer and was certain a simple reboot would work. Within minutes he emailed me some Brother instructions and it worked! I wish I had called him earlier in the day, it would have saved me from getting extremely frustrated. Thank you Greg and Printer Repair Experts!
Desirae R. Google Reviews
